[1]刘敏珊,张丽娜,董其伍..45°涡轮桨搅拌槽内搅拌特性数值模拟研究[J].郑州大学学报(工学版),2008,29(01):1-4.[doi:10.3969/j.issn.1671-6833.2013.01.001]
 LIU Minshan,ZHANG Lina,Dong Qiwu.Numerical simulation study of stirring characteristics in 45° turbine stirring tank[J].Journal of Zhengzhou University (Engineering Science),2008,29(01):1-4.[doi:10.3969/j.issn.1671-6833.2013.01.001]
点击复制

45°涡轮桨搅拌槽内搅拌特性数值模拟研究()
分享到:

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
29
期数:
2008年01期
页码:
1-4
栏目:
出版日期:
1900-01-01

文章信息/Info

Title:
Numerical simulation study of stirring characteristics in 45° turbine stirring tank
作者:
刘敏珊张丽娜董其伍.
郑州大学,热能工程研究中心,河南,郑州,450002, 郑州大学,热能工程研究中心,河南,郑州,450002, 郑州大学,热能工程研究中心,河南,郑州,450002
Author(s):
LIU Minshan; ZHANG Lina; Dong Qiwu
关键词:
折叶涡轮桨 数值模拟 搅拌特性
Keywords:
DOI:
10.3969/j.issn.1671-6833.2013.01.001
文献标志码:
A
摘要:
采用多重参考系法(MRF)及标准k-ε模型对工业中广泛应用的45°折叶涡轮桨搅拌槽内的搅拌特性进行模拟,考察不同监测点对混合效果的响应情况,发现不同监测点的响应出现明显的差别.对搅拌桨距槽底距离变化时,槽内搅拌流型以及速度矢量的分布和功率消耗情况进行模拟研究,结果表明:当C/T为0.278时,槽内流型发生转变;当流型转变时,搅拌桨消耗功率达到最低.
Abstract:

The multiple reference frame method (MRF) and standard k-ε model were used to simulate the stirring characteristics in the 45° folding blade turbine stirring tank widely used in industry, and the response of different monitoring points to the mixing effect was investigated, and obvious differences were found in the response of different monitoring points. The simulation study of the stirring flow pattern in the tank and the distribution and power consumption of the velocity vector when the distance from the bottom of the mixing paddle is changed, and the results show that when the C/T is 0.278, the flow pattern in the tank changes. When the flow pattern is changed, the power consumption of the impeller reaches a minimum.

相似文献/References:

[1]时刚,田新涛.工程卡车行驶引发地面振动特性研究[J].郑州大学学报(工学版),2020,41(05):76.[doi:10.13705/j.issn.1671-6833.2020.03.017]
 SHI Gang,TIAN Xintao.Research on Ground Vibration Characteristics Caused by Engineering Truck Driving[J].Journal of Zhengzhou University (Engineering Science),2020,41(01):76.[doi:10.13705/j.issn.1671-6833.2020.03.017]
[2]戴逸飞,杨 平,王 宁,等.交叠车站下穿段MJS加固温度场变化规律研究[J].郑州大学学报(工学版),2023,44(01):103.[doi:10.13705/j.issn.1671-6833.2022.04.002]
 DAI Yifei,YANG Ping,WANG Ning,et al.Study on Temperature Field Variation Law of MJS Reinforcement for Underpass Section of Overlapping Station[J].Journal of Zhengzhou University (Engineering Science),2023,44(01):103.[doi:10.13705/j.issn.1671-6833.2022.04.002]
[3]王定标,万方方,周俊杰..蒸发式冷凝器异型扁管性能分析及数值模拟[J].郑州大学学报(工学版),2010,31(02):67.
 WANG Dingbiao,WANG Fangfang,Zhou Junjie.Performance Analysis and Numerical Simulation of EvaporativeCondenser with Special—-shaped Flat Tube[J].Journal of Zhengzhou University (Engineering Science),2010,31(01):67.
[4]董其伍,王烨,刘敏珊..流动冲击角对流体绕流管束换热的影响[J].郑州大学学报(工学版),2010,31(02):0.
 DONG Qiwu,WANG Ye,LIU Minshan.Influence of Flowing Impact Angle Heat Transfer in Fluid Flowing Across Tube Bundles[J].Journal of Zhengzhou University (Engineering Science),2010,31(01):0.
[5]王丹,董其伍,刘敏珊..管壳式换热器模块综合模拟方法研究[J].郑州大学学报(工学版),2010,31(03):20.
 WANG Dan,DONG Qiwu,LIU Minshan.Study on Module Synthesis Simulation Method forShell-and-Tube Heat Exchanger[J].Journal of Zhengzhou University (Engineering Science),2010,31(01):20.
[6]李成,马志垒,王永涛..冲击荷载下防弹钢板三维损伤分析[J].郑州大学学报(工学版),2010,31(04):85.[doi:10.3969/j.issn.1671-6833.2010.04.021]
[7]王定标,雷风林,向飒,等.汽轮机末级变工况三维数值模拟与叶型改进设计[J].郑州大学学报(工学版),2010,31(05):1.[doi:10.3969/j.issn.1671-6833.2010.05.001]
[8]张兆宁,贺拴海,赵煜..基于应力控制箱梁截面设计数值模拟分析[J].郑州大学学报(工学版),2010,31(06):65.[doi:10.3969/j.issn.1671-6833.2010.06.016]
[9]汪磊,李涛..海底隧道穿越断层破碎带预注浆加固稳定性分析[J].郑州大学学报(工学版),2010,31(06):73.[doi:10.3969/j.issn.1671-6833.2010.06.018]
[10]魏新利,张富强,简士钊,等.以制冷剂R22为工质的地板辐射采暖模拟与优化[J].郑州大学学报(工学版),2011,32(02):6.[doi:10.3969/j.issn.1671-6833.2011.02.002]

更新日期/Last Update: 1900-01-01