[1]袁守利,林家辉.FSAE方程式赛车车架的设计与轻量化[J].郑州大学学报(工学版),2018,39(04):18-24.[doi:1013705/j.issn.1671-6833.2018.01.005]
 Yuan Shouli,Lam Ka Fai.The Design of  FSAE Formula Frame Light weight[J].Journal of Zhengzhou University (Engineering Science),2018,39(04):18-24.[doi:1013705/j.issn.1671-6833.2018.01.005]
点击复制

FSAE方程式赛车车架的设计与轻量化()
分享到:

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
39卷
期数:
2018年04期
页码:
18-24
栏目:
出版日期:
2018-07-22

文章信息/Info

Title:
The Design of  FSAE Formula Frame Light weight
作者:
袁守利林家辉
武汉理工大学 汽车工程学院,湖北 武汉,430070
Author(s):
Yuan Shouli; Lam Ka Fai
School of Automotive Engineering, Wuhan University of Technology, Wuhan, 430070
关键词:
Keywords:
Formula Structure design The finite element analysis Lightweight The modal calculation
DOI:
1013705/j.issn.1671-6833.2018.01.005
文献标志码:
A
摘要:
为满足FSAE(Formula Student Automobile Equation)方程式赛车车架强度和刚度的要求,其安全裕度较大,为充分挖掘车架的轻量化潜力,运用有限元分析软件依次对车架进行了SIMP方法的拓扑设计和截面尺寸优化,通过改变模型参数值,同时在网格模型保持不变的情况下,采用尺寸优化设计技术模拟三种实际赛道工况,在保证刚度和强度前提下车架最大变形量相应减少了7%,7.5%,14.7%,最大应力在200MPa以内,车架质量减少了32%,最后通过模态和试验分析,优化设计的车架有效避开了对外部激励的耦合效应,8字绕环测试所用的时间减少了3%。该赛车车架达到了轻量化的目的。
Abstract:
The safety margin of FSAE (Formula Student Automobile Equation) racing car should be lager. To meet the requirements of strength and stiffness, fully tap the potential for lightweight frame.This paper optimized topology design and section size of car frame in the SIMP method with the finite element analysis software. Considering the mesh of model remains unchanged and simulating three track actual conditions by the size of optimization method, we change the model parameter values,and the corresponding maximum deformation of car’s frame decreases by 7%, 7.5%, 14.7% respectively under the certain strengh and stiffness of car’s frame. When the maximum stress was less than 200MPa, the quality of the frame was reduced by 32%. Finally, through the modal analysis and test, optimization design of frame could effectively avoid the coupling effect and external excitation, the eight around the ring tesr time could be reduced by 3%. The racing car frame achieveed the purpose of light weight.

相似文献/References:

[1]张正国.斜对接焊缝强度计算问题——钢结构设计规范讨论[J].郑州大学学报(工学版),1991,12(01):55.
 Zhang Zhengguo,Calculation problem of obliquely connected welds -Discussion on Steel Structure Design Specifications[J].Journal of Zhengzhou University (Engineering Science),1991,12(04):55.
[2]徐长白,杨宙飞,徐献中,等.ZZ812型垂直分型无箱射挤压造型机的设计[J].郑州大学学报(工学版),1987,8(01):95.
 [J].Journal of Zhengzhou University (Engineering Science),1987,8(04):95.
[3]陈丰,曾凡才.“简易空间机器人”机械结构设计[J].郑州大学学报(工学版),1989,10(03):70.
 [J].Journal of Zhengzhou University (Engineering Science),1989,10(04):70.

更新日期/Last Update: 2018-07-25