[1]刘竹丽赵敏敏马朋朋.基于ANSYS的斜齿轮副接触分析与可靠性分析[J].郑州大学学报(工学版),2015,36(02):6-9.[doi:10.3969/ j. issn.1671 -6833.2015.02.002]
　LIU Zhu-li,ZHAO Min-min,MA Peng-peng,et al.Large Helical Gears Contact Analysis and Contact StrengthReliability Analysis Based on ANSYs[J].Journal of Zhengzhou University (Engineering Science),2015,36(02):6-9.[doi:10.3969/ j. issn.1671 -6833.2015.02.002]
点击复制

基于ANSYS的斜齿轮副接触分析与可靠性分析()
分享到：

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
36
期数:
2015年02期
页码:
6-9
栏目:
出版日期:
2015-04-30

文章信息/Info

Title:
Large Helical Gears Contact Analysis and Contact StrengthReliability Analysis Based on ANSYs
作者:
刘竹丽1赵敏敏2马朋朋3
郑州大学机械工程学院,河南郑州450001
Author(s):
LIU Zhu-li; ZHAO Min-min; MA Peng-peng; QIN Dong-chen
School of Mechanical Engineering,Zhengzhou University ,Zhengzhou 450001,China
关键词:
斜齿轮; ANSYS; 接触分析; 可靠性分析
Keywords:
helical gear ; ANSYs;  contact analysis ;  reliability analysis
分类号:
th132.4
DOI:
10.3969/ j. issn.1671 -6833.2015.02.002
文献标志码:
A
摘要:
针对某大型传动装置中的一对斜齿轮,在Solidworks中建立了其装配模型,然后将其导入有限元分析软件ANSYS中进行接触应力分析,且将接触应力计算结果与传统接触应力计算结果进行比较;最后在ANSYS中针对该斜齿轮副的接触强度可靠性进行分析,结果表明:该斜齿轮副实际接触应力小于其许用接触应力,接触强度满足使用要求,但是其可靠度仅为83.6398% ,说明按传统的机械设计方法只进行安全系数的计算是不够的,还需要进行可靠性设计计算;此外,由各随机因素对极限状态函数的灵敏度可知,适当增大从动齿轮分度圆直径可有效提高斜齿轮副可靠度.
Abstract:
For a helical gear vice in a large transmission device,assembly model is created in Solidworks, andthen it is imported into the finite element analysis software ANSYS and stress analysis is contacted. Besides ,the contact stress calculation results and the traditional contact stress calculation results is compared;Finally ,the contact stress reliability in ANSYS is analyzed. The results show that : the helical gear vice actual contactstress is less than the allowable contact stress,and meet the requirements,but its reliability is only 83.6398%, which means by traditional method which only counts the mechanical design safety factor is not e-nough;Besides, from the sensitivity of random factors to detss , we know that increasing driven wheel diametercan improve the reliability effectively.

相似文献/References:

[1]周浩,刘竹丽,侯东红.QT280拖挂式牵引机牵引轮结构分析与优化[J].郑州大学学报(工学版),2016,37(01):79.[doi:10.3969/j.issn.1671-6833.201411034]
　Liu Zhuli,Zhou Hao,Hou Donghong.Finite Element Analysis and Optimization of QT280 Trailer-Tractor Entry Capstan[J].Journal of Zhengzhou University (Engineering Science),2016,37(02):79.[doi:10.3969/j.issn.1671-6833.201411034]
[2]刘竹丽,陈赟,王祝新.齿面残余应力对齿轮轮齿弯曲疲劳寿命的影响分析[J].郑州大学学报(工学版),2020,41(03):53.[doi:10.13705/j.issn.1671-6833.2019.02.013]
　Liu Zhuli,Chen Yun,Wang Zhuxin.The analysis of the residual stress of tooth surfaces influence on the flexural fatigue life of gear tooth[J].Journal of Zhengzhou University (Engineering Science),2020,41(02):53.[doi:10.13705/j.issn.1671-6833.2019.02.013]

更新日期/Last Update: