[1]宋建学,袁英保,刘贺龙..旅游栈道安全评价技术研究[J].郑州大学学报(工学版),2008,29(03):129-132.[doi:10.3969/j.issn.1671-6833.2008.03.033]
 SONG Jianxue,Yuan Yingbao,Liu Helong.Research on safety evaluation technology of tourism boardwalk[J].Journal of Zhengzhou University (Engineering Science),2008,29(03):129-132.[doi:10.3969/j.issn.1671-6833.2008.03.033]
点击复制

旅游栈道安全评价技术研究()
分享到:

《郑州大学学报(工学版)》[ISSN:1671-6833/CN:41-1339/T]

卷:
29
期数:
2008年03期
页码:
129-132
栏目:
出版日期:
1900-01-01

文章信息/Info

Title:
Research on safety evaluation technology of tourism boardwalk
作者:
宋建学袁英保刘贺龙.
郑州大学,土木工程学院,河南,郑州,450001, 郑州大学,土木工程学院,河南,郑州,450001, 郑州大学,土木工程学院,河南,郑州,450001
Author(s):
SONG Jianxue; Yuan Yingbao; Liu Helong
关键词:
杆件结构 力学模型 栈道 安全评价
Keywords:
DOI:
10.3969/j.issn.1671-6833.2008.03.033
文献标志码:
A
摘要:
旅游景区栈道通常就地取材,设计、施工技术资料不详,并经常发生人员拥挤现象,存在安全隐患.提出栈道安全评价技术路线,其内容包括栈道依附的岩体、栈道与岩体结点、栈遭结构本身及栈道附属结构等4项;根据结点连结方式不同,建立悬挑式、立柱式、斜柱式栈道力学分析模型.按照实际栈道调查,分别对8种模型在相应荷载下的弯矩、轴力和剪力对比分析,发现最大弯矩和剪力出现在水平横梁上,最大轴力出现在斜支撑上,进而提出栈道最不利内力验算模式.结合案例工程,对栈道工程实例进行安全评价,验证了分析模型的适用性.
Abstract:
Plank roads in tourist attractions are usually made of local materials, the design and construction technical information are unknown, and crowding often occurs, which has potential safety hazards. The technical route of safety evaluation of plank road is proposed, including four items: the rock mass attached to the plank road, the node of the plank road and the rock mass, the stack structure itself and the auxiliary structure of the plank road. According to the different connection methods of nodes, the mechanical analysis models of cantilever, column and oblique column planks are established. According to the actual plank road investigation, the bending moment, axial force and shear force of the eight models under the corresponding load were compared and analyzed, and it was found that the maximum bending moment and shear force appeared on the horizontal beam and the maximum axial force appeared on the oblique support, and then the most unfavorable internal force verification mode of the plank road was proposed. Combined with the case project, the safety evaluation of the plank road engineering example is carried out, and the applicability of the analysis model is verified.

相似文献/References:

[1]郑艳萍,赵江铭,曹遂军..对称变换在对称型微结构建模中的应用[J].郑州大学学报(工学版),2003,24(03):87.[doi:10.3969/j.issn.1671-6833.2003.03.022]
[2]袁昕,韩林山..桥式抓斗起重机钢丝绳卷绕系统动态分析[J].郑州大学学报(工学版),1999,20(03):76.[doi:10.3969/j.issn.1671-6833.1999.03.026]
[3]袁 峰,刘凌仲,秦东晨,等.CT 机双列角接触球转盘轴承建模与振动特性分析[J].郑州大学学报(工学版),2024,45(05):23.[doi:10.13705/j.issn.1671-6833.2024.05.007]
 YUAN Feng,LIU Lingzhong,QIN Dongchen,et al.Modeling and Vibration Characteristics Analysis of Double-rowAngular Contact Ball Turntable Bearings in CT Machine[J].Journal of Zhengzhou University (Engineering Science),2024,45(03):23.[doi:10.13705/j.issn.1671-6833.2024.05.007]

更新日期/Last Update: 1900-01-01